loading

Professional O-Ring and Oil Seal Manufacturer, Sealing Solution Supplier Since 2008.

NOK Replacement AP1260E TCV Oil Seal 24×40×8 1
NOK Replacement AP1260E TCV Oil Seal 24×40×8 2
NOK Replacement AP1260E TCV Oil Seal 24×40×8 3
NOK Replacement AP1260E TCV Oil Seal 24×40×8 4
NOK Replacement AP1260E TCV Oil Seal 24×40×8 5
NOK Replacement AP1260E TCV Oil Seal 24×40×8 6
NOK Replacement AP1260E TCV Oil Seal 24×40×8 7
NOK Replacement AP1260E TCV Oil Seal 24×40×8 8
NOK Replacement AP1260E TCV Oil Seal 24×40×8 9
NOK Replacement AP1260E TCV Oil Seal 24×40×8 10
NOK Replacement AP1260E TCV Oil Seal 24×40×8 1
NOK Replacement AP1260E TCV Oil Seal 24×40×8 2
NOK Replacement AP1260E TCV Oil Seal 24×40×8 3
NOK Replacement AP1260E TCV Oil Seal 24×40×8 4
NOK Replacement AP1260E TCV Oil Seal 24×40×8 5
NOK Replacement AP1260E TCV Oil Seal 24×40×8 6
NOK Replacement AP1260E TCV Oil Seal 24×40×8 7
NOK Replacement AP1260E TCV Oil Seal 24×40×8 8
NOK Replacement AP1260E TCV Oil Seal 24×40×8 9
NOK Replacement AP1260E TCV Oil Seal 24×40×8 10

NOK Replacement AP1260E TCV Oil Seal 24×40×8

  • Category:Rotary Shaft Oil Seal
  • Temperature:-30℃ ~ 120℃
  • Pressure:Max continuous 0.3MPa, peak 0.5MPa
  • Material:NBR
  • Color:Black
  • Product description:AP1260E TCV BABSL oil seal, 24×40×8mm, double lip with garter spring, rubber coated metal case, for excavator pilot pump, hydraulic gear pump and orbit motor.
5.0
design customization

    oops...!

    no product data.

    Go to homepage

    More Choices

    AP1260E (AP1260E0) TCV BABSL Rotary Shaft Oil Seal

    Size: ID24 × OD40 × H8 mm

    TCV type seal is a reinforced back-pressure resistant skeleton oil seal, double lip design with garter spring and rubber coated metal case. It is widely used for rotary shafts with residual back pressure, commonly known as pump shaft seal for mini excavator pilot pump, gear pump and orbit hydraulic motor.

    1. Structure

    • Primary sealing lip with garter spring: maintains stable radial compression, prevents lip turning over under back pressure
    • Secondary dust lip (air side): blocks dust, sand and splash water to protect main lip
    • Carbon steel metal frame, fully rubber coated outer diameter: better housing sealing, avoids outer race slipping and leakage
    • Standard material: NBR; FKM is available for high temperature & special oil condition

    2. Technical Specifications

    • Material: NBR (standard) / FKM (optional)
    • Max continuous working pressure: 0.3 MPa
    • Peak instantaneous pressure: ≤0.5 MPa
    • Max shaft linear speed: ≤15 m/s
    • Temperature range (NBR): -30℃ ~ +120℃
    • Temperature range (FKM): -20℃ ~ +200℃
    • Suitable media: mineral hydraulic oil, gear oil, lubricating grease
    • Shaft recommended roughness: Ra 0.2~0.8 μm
    • Shaft hardness: HRC ≥45
    • Housing tolerance: H7

    3. Application

    Mini excavator pilot pump, hydraulic gear pump, orbit hydraulic motor, small swing motor, agricultural hydraulic pump, forklift hydraulic power unit and other construction machinery hydraulic parts.

    4. Important Notes

    • AP1260E = AP1260E0, same part
    • AP1260F is same dimension but different lip profile, NOT interchangeable
    • TCN version looks similar but with internal support ring, higher pressure rating, NOT equal to original NOK TCV AP1260E
    • Ordinary TC seal cannot withstand back pressure, do not substitute for TCV

    5. Installation Guide

    1. Install correctly: spring side towards oil / pressure side, dust lip to air side. Reverse installation will cause leakage immediately.
    2. Shaft chamfer 30°~45°, remove burrs. Use installation sleeve to protect sealing lip from damage by keyway or thread.
    3. Press uniformly with proper sleeve, no hammering or inclined pressing.
    4. Lubricate seal lip before installation, dry running on start-up is prohibited.
    5. Storage: keep away from direct sunlight, normal temperature environment. Recommended shelf life ≤24 months.

    6. Common Failure Reasons

    Exceed continuous back pressure limit, shaft scratch/groove, lip damage during installation, reversed installation, incompatible fluid, over speed and high friction heat aging.

    Get In Touch With Us

    We are committed to meeting the diverse needs of our global customers through innovation and continuous improvement.

    Need more information?
    If you didn't find what you need, you can send an inquiry through our contact form.
    Please fill in the form below.
    Contact Us
    Customer service